[ Pobierz całość w formacie PDF ]
4. Remove the upper case assembly (Section 5.6).
5. Remove the I/O assembly (Section 5.9).
6. Remove the top brace (Section 5.10).
7. Disconnect and untuck the control panel cable from the backplane assembly (Section
5.13).
8. Remove the mechanism assembly (Section 5.15).
9. Remove the power supply (Section 5.16).
10. Remove the backplane assembly (Section 5.17).
11. Position the ArmadaStation so the left side is facing forward.
ArmadaStation Removal and Replacement Procedures 5-59
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
12. Flex the right bottom side of the expansion card cage away from the retainer on the
1 2
base assembly and swing the cage up and away (Figure 5-55).
Figure 5-55. Releasing the Expansion Card Cage
5-60 ArmadaStation Removal and Replacement Procedures
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
13. Swing the expansion card cage to the right until the tabs on the right side of the cage
clear the slots in the base assembly (Figure 5-56).
Figure 5-56. Removing the Expansion Card Cage
Reverse the removal procedure described above to install the backplane assembly.
ArmadaStation Removal and Replacement Procedures 5-61
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Chapter 6
Armada MiniStation Removal and
Replacement Procedures
This chapter presents the removal and replacement procedures for the Armada
MiniStation.
NOTE: This chapter contains instructions that refer to the Armada MiniStation in its two
optional models: the Armada MiniStation E (Ethernet capability) and the Armada
MiniStation EX (Ethernet, MultiBay, battery charging bay, and PC Card capabilities).
When a set of instructions refers to the Armada MiniStation, the instructions pertain
to both models. Otherwise, E or EX is used to indicate the specific model base.
6.1 Serial Number
The Armada MiniStation serial number should be reported to Compaq when requesting
information or ordering spare parts. The serial number is displayed on the left side of
the Armada MiniStation (Figure 6-1).
Figure 6-1. Armada MiniStation Serial Number Location
Armada MiniStation Removal and Replacement Procedures 6-1
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.2 Disassembly Sequence Chart
Use the chart below to determine the section number and disassembly sequence for
removing components from the Armada MiniStation.
6.3 Preparing the Armada MiniStation for
Disassembly
6.4 External Components
Compaq Logo
Armada MiniStation Feet
6.5 Enclosure Cover
6.6 Module Assembly
6.7 Power Supply
6.8 MultiBay/PC Card Assembly
Figure 6-2. Armada MiniStation Disassembly Sequence Chart
6-2 Armada MiniStation Removal and Replacement Procedures
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.3 Preparing the Armada MiniStation
for Disassembly
Before beginning removal and replacement procedures, follow these steps:
1. Turn the Armada MiniStation EX keylock counterclockwise to unlock it.
2. Undock the computer from the Armada MiniStation.
1
3. Disconnect the power cord from the wall outlet (Figure 6-3).
2
4. Disconnect the power cord from the Armada MiniStation .
Figure 6-3. Disconnecting the Armada MiniStation
5. Disconnect external devices.
6. If installed, remove the battery pack from the battery charging bay (Armada
MiniStation EX only).
7. If installed, remove the MultiBay device from the MultiBay (Armada
MiniStation EX only).
8. If installed, remove the PC Cards from the PC Card slots (Armada MiniStation EX
only).
Armada MiniStation Removal and Replacement Procedures 6-3
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.4 External Components
This section describes the removal and replacement procedures that do not require
access to the internal components of the Armada MiniStation. This includes:
Compaq logo
Feet
Compaq Logo
A Compaq logo should be installed on the Armada MiniStation or monitor support
cover only if the old logo is damaged or removed. The logo is an adhesive-backed label.
Remove the protective covering from the adhesive back, and install the logo in its
location on the Armada MiniStation (Figure 6-4). The logo reads from left to right
when viewed from the front of the unit.
Figure 6-4. Installing a Compaq Logo
6-4 Armada MiniStation Removal and Replacement Procedures
[ Pobierz całość w formacie PDF ]